Scaffolding jack base with nut:
1. Material: Q235
2. Surface treatment: Electro-plated
3. OEM service and customer's size are both available
4. Main market: America, Australia, South Asia, etc.
5. Factory direct supply, competitive price

1. Weight: 0.33KG
2. Size: 69*105*3mm
3. Material: Q235
4. Material of Wedge: 65Mn
5. Surface Treatment: Electrostatic spraying

Swift Lift Plus Recess Plug is manufactured from high-grade elastomeric, thermal set urethane to provide improved tear, heat and chemical resistance. The versatile, reusable plug utilizes a variety of accessories to provide installation and stripping ease in many
different applications. Rplugs are available for 1, 2, 4 and 8-ton system sizes.

The formed head provides spherical seating that the Lifting Eye engages, while a disc-shaped foot is embedded in the concrete. Due to its being a forged part, the Swift Lift Anchor does not depend on welds or thread engagement to develop its safe working load. Forging provides maximum safety with its advantageous material structure.  In addition to the carbon steel anchors, Type 304 or 316 Stainless Steel Swift Lift Anchors are available on special order. Use stainless steel anchors when maximum protection against corrosion is required.

Our products range from wing nuts, water stops, hex nuts, couplers, and washers/plates to tie rods, all for the nominal thread diameter 15mm (DG 15/17), other sizes of thread available on request.

 

The formworks refer to the products wing nut,hex nut,Flange nut,Hex coupler and so on.

The nailing plate is used to fix the socket anchors to the formwork. Thread sizes M/Rd12 to M/Rd52 are available. The nailing plate is made of plastic, and is color coded according to the thread size. The recess formed by the nail plate is perfect fit for the Kingfix transport anchor system. this allows the head of lifter to bear on the concrete during diagonal and transverse lifting.

Anchor channels

Application

The cold Rolled Anchor Channel is made from Cold-rolled Profile, it's an economical and simple solution for most applications.

Material

Constructed of cold-formed C-shaped channels with anchor bolts swaged on to transfer the load into the concrete. Our anchor channels are filled with polyethylene foam fillers.

The cold Rolled Anchor Channel is made from Cold-rolled Profile, it's an economical and simple solution for most applications.

1 Size: 28/15,38/17,40/25,49/30,40/22,50/30,52/34

2 Stamping channels or hot rolled channels

3 High tensile load.

anchor channel:

Application

The Hot Rolled Anchor Channel is made from Hot-rolled Profile, which provides better performances for dynamic loads and

Material

Constructed of hot-formed C-shaped channels with anchor bolts swaged on to transfer the load into the concrete.

(1)material:carbon steel or stainless steel.
(2)weight:1.25kg/m-3.22kg/m.
(3)surface:GALV. or YELLOW GALV.

(4)delivery detail:within 30 days.

(5)packing detail:plywood case or steel pallet.

Rubber recess formers

The Recess former can receive all our anchors in load groups of 2.5 t, 5.0 t, 7.5T and 10.0 t.

1) Material: rubber
2) Specification:1.3T 2.5T 5T 10T 20T
3) Color:black,yellow,red,blue. 

Lifting Ring Clutch 

The ring clutch is composed of a shackle and a lifting head, the free moving shacle gives the clutch great flexibility during the loading while the locking bolt in the lifting head makes it so easy to hook the anchor and secure the lifting. We provide 3 load classes of this clutch.

Lifting Loop/eyebolt is used for lifting precast concrete elements with precast anchors inside, the eyebolt can work under both straight pull and shear pull loads while lifting loop is supposed to work under straight pull situation only.

The cast-in loop is used to lift reinforced concrete elements. The cast-in loops are marked with a coloured tag with the manufacturer, year of manufacture and load group. The cast-in loop is situated in the concrete element at the open side of the mould. The thimble is situated in the mould. The marking must be visible after placing the concrete. Hoisting hooks of appropriate diameter can be inserted directly into the protruding cast-in loop. Care must be taken whenstoring the prefabricated element that the cables do not kink. The withdrawal from use of the lifting loops is to be determined in accordance with the regulations for hoisting cables of the country of use. The installation and application of lifting anchor systems must be available in plant and on site.The national safety regulations for lifting anchors and sytems must be obeyed.

Dogbone anchors:

Swift Lift Stud and Wing Nut combination is used to set Narrow Recess Plugs.
Available in two sizes, 18 NC threads for use with the 1-ton anchor and NC threads for use with 2, 4, 8 and
20-ton anchors.

Utility Anchors are available in three diameters and a series of lengths for specific concrete thickness. The utility anchor can be set in either a 90° or a 45° anchor orientation using the appropriate setting plug.

The anchoring of the JPL, SBKL and PKL fastening plates is based on the concrete cone which is due to the headed studs. Bending of the anchors reduces the capacities of tension and moment of fastening plates because it downsizes the concrete cone. In the case of bending the anchors the capacities of  the fastening plate must be checked.

SBKL, KL, JPL and PKL fastening plates are steelparts that are installed before the concrete hardens. The plates transfer the loads from plate to the concrete structure.Structural fi xings are made by welding to the steel plate.

Two Hole Anchor is always used in conjunction with the Tension Bar. The anchor has a bottom hole especially designed to accept the tension bar. Place the  Tension Bar through the bottom hole in such a manner that the ends of the tension bar are pointing downward. Fasten the tension bar tight against the bottom side of the hole. The tension bar distributes the tension forces, developed from the lifting process, deep into the precast concrete.

Swift Lift Universal Lifting Eye consists of a flat-sided, spherical lifting body and a high strength bail. The lifting body has a T-shaped slot that permits rapid attachment and release of the head on Swift Lift Anchors.

Throw Away Recess Plug is fabricated from high-density polyethylene plastic in two sizes (2-ton and 4-ton) to accommodate the Swift Lift Anchor. The two-piece design snaps together around the head of the anchor to securely grasp the anchor. Tabs on the recess plug provide a convenient method to nail the assembly to the form. Built-in retainers allow a Shear Bar to clip to therecess plug and be held in correct position. The recess plug is designed to properly position the anchor below the surface of the concrete. This allows easy patching of the recess and prevents surface staining from exposed steel.

Lift eye anchors:

Lifting Stud w/t Foot Eye is mainly designed for the use in slender reinforced concrete elements,e.g. beams and girders. It is also suitable for lightweight concrete elements, please take the reduced bond stresses into account

Flat Washers are manufactured from high carbon flat steel plates and are designed to provide the required bearing against the form members.

Reusable and durable Steel Chamfer is designed to create beveled edges on the corners and faces of concrete wall panels and small concrete items.

Sandwich panel anchor  is specially designed for use with precast sandwich panels. Its suspension point is close to the gravity
axis thus allowing the element to be transported and erected in an upright position.

The special shaped anchor head means that the pitching/turning loads are taken by the anchor and not to the concrete. This helps to prevent spalling of the concrete. The anchors are notched to assist with the placement of additional reinforcement required in the pitching/turning operation.

Application

Fixing Insert w/t bended end are used for the fixing of light weight precast-concrete units. Easy to use cause no reinforcement bar required.

Material

Seamless Precision tube, galvanized. Stainless steel available on request

Specification:
1) product name:fixing sockets
2) complete range of sizes
3) other sizes on request

Fixing Inserts are used for the fixing of light weight precast-concrete units. A reinforcement tail must be used for the transmission of the load into the concrete.

The Bolt Anchor type I is suitable for transporting precast concrete components of varying dimensions. Thin flat slabs, facing panels, beams of columns can all be easily transported by Bolt Anchors. The load is transferred into the concrete through the bolt so generally no additional reinforcement is needed.

Application

Heavy Duty Lifting/Fixing sockets for high tensile and shear loads. Widely used in the application of precast concrete construction, such as lifting beams, wall and floor slabs etc.. A Reinforcement bar is to be inserted through the cross hole to transfer the load into the concrete.

Material

High Strength Solid bar, galvanized. Stainless steel available on request.

Application

Solid Rod Socket( Heavy Duty Lifting/Fixing sockets) for high tensile and shear loads. Widely used in the application of precast concrete construction, such as lifting beams, wall and floor slabs etc.. A Reinforcement bar is to be inserted through the cross hole to transfer the load into the concrete.

Material

High Strength Solid bar, galvanized. Stainless steel available on request.

1) Product: Lifting socket,lifting insert,bend and waved socket, transport socket,flat socket
   ,socket with bar and so on.
2) Diameter: M / RD 12 - 52mm
3) Length: 40 - 200mm

4) Capacity: 0.5 - 12.5MT
5) Material: stainless 304/316, ST52.3
6) Surface: plain, galvanized.

Lifting Insert is a M threaded insert for the lifting purpose. It can be used for the transport of beams, panels and slabs etc. A rebar must be passed through the cross hole to transfer the load into the concrete.

Application

Wavy Tail Anchor is suitable for transporting very thin-walled precast components such as thin walls, flat panels etc., Even precast mansory wall components can be transported with this Wavy Tail Anchor.

Material

Seamless precision tube with high strength rebar. Stainless Steel tube c/w rebar hot Zinc-Sprayed.

Application

Short Anchors are suitable for lifting the light weight flat units The advantage is that in most cases no additional reinforcement is needed as the load is transferred through the crown foot to the concrete.

Material

High Strength Steel, Galvanized. Stainless steel available on request.

Application

Suitable for transporting precast concrete components of varying dimensions. Thin flat slabs, facing panels, beams or columns can all be easily transported by this Combi Anchor. The load is transferred into the concrete through the round foot so generally no additional reinforcement is needed.

Material

Seamless precision tube with high strength rebar. Stainless Steel tube c/w rebar hot Zinc-Sprayed.

Application

Bar Anchor is suitable for transporting very thin-walled precast components such as thin walls, flat panels etc., Even precast masonry wall components can be transported with this Bar Anchor.

Material

Seamless precision tube with high strength rebar. Stainless Steel tube c/w rebar hot Zinc-Sprayed.

Technical Data

Application

Flat Lifting Socket is ideal for large, thin precast concrete components such as slabs and shells, on which it's hard to place normal lifting sockets because of the thin thickness of the component. Additional reinforcement must be used to transmit the load into the concrete.

Material

Seamless Precision tube and high strength steel plate.

Size: RD12-RD52mm

Broken load: more than 4 times.

Capped End lifting insert and Screw Anchor insert for thin units
– Low profile socket fully welded to plate; reinforcement must be installed in the yard
– Used in the face of thin units and for long term reuse for maintenance
– Available in12 – 52mm diameters, giving load capacity of 500 – 12,500 kg
– Use with Threaded lifting loop or Swivel lifting eye

Lifting Sockets:

Features:

1) Product: Lifting socket,lifting insert,bend and waved socket, transport socket, flat         socket, socket with bar and so on.
2) Diameter: M / RD 12 - 52mm
3) Length: 40 - 200mm

4) Capacity: 0.5 - 12.5MT
5) Material: stainless 304/316, ST52.3
6) Surface: plain, galvanized

lifting inserts and lifting sockets for the precast system

Lifting socket

Transport anchor,Lifting socket

W Swift Lift Anchor:

W Swift Lift Anchors are the shortest 2-ton and 4-ton Swift Lift Anchors available and
have been specially modified. A Type W Plain Washer is placed on the anchor’s foot and welded
in position. This modification has been made in order to increase the Safe Working Load of these
short Swift Lift Anchors in thin precast concrete elements.
Safe Working Load provides a factor of safety of approximately 4 to 1.

precast part utility anchor easy anchor lift anchor double head anchor plate anchor spherical anchor rod anchor,T slot anchors

Superior Lift Insert is a face-lift insert and consists of a  foot anchor, 4-leg wire base and plastic void former. The insert utilizes the Ring Clutch 8-10 T. The Superior Lift Inserts are shipped assembled, ready-to-use and are sized 1/8” less than the panel thickness.

Swift Lift Plus Threaded Plate,Swift Lift Plus Stud Plate,Swift Lift Plus Holding Plate
The Swift Lift Plus Threaded Plate, Stud Plate and Holding Plate are working
parts used to install the Recess Plug in various applications. These working parts are available in 1, 2, 4 and 8-ton
system sizes.

Swift Lift Steel Recess Plug is
designed for permanent or semi-permanent attachment to
repetitive-use precast forms, such as battery molds, steel forms
that have a collapsible stripping feature, etc. The recess plug is
drilled and tapped for easy attachment to the form or may be held
in place by a magnetic plate, tack welded or glued.

Swift Lift Narrow Recess Plug is designed for use in thin-wall conditions, such as the top edge of
highway safety barriers. The recess plug is bolted to the form using a stud and wing nut combination and it correctly
positions the anchor below the surface of the concrete. Rrecess plugs are fabricated from nitrile butadiene and are ideal for
use in conditions requiring temperature or oil resistance.

Swift Lift Tension Bar  is designed to be used with the P-53 Eye Anchor in order for the
eye anchor to develop its published rated working loads.

W Swift Lift Anchors are the shortest 2-ton and 4-ton Swift Lift Anchors available and
have been specially modified. A Type W Plain Washer is placed on the anchor’s foot and welded
in position. This modification has been made in order to increase the Safe Working Load of these
short Swift Lift Anchors in thin precast concrete elements.
Safe Working Load provides a factor of safety of approximately 4 to 1.

waved socket

1) Product: lifting and connect socket; flat, bend and waved socket, socket    with ring, socket with bar, swivel lifting eye and accessory 

2) Diameter: M / RD 12 - 52mm

3) Length: 50 - 200mm (2 - 8")

4) Capacity: 0.5 - 12.5MT

5) Material: stainless 304/316, ST52.3

6) Surface: plain, galvanized

7) Products available: swivel lifting eye screw, eye screw, lifting loop for socket

 F-42 Loop Ferrule Insert is fabricated by welding a looped strut to a closed-end ferrule. F-42 insert is available in the sizes shown in the chart and is well suited for structural connections and the suspension of equipment, piping, etc. Minimum spacing between inserts is twice the minimum corner distance.

The coil insets refer to kinds of products such as:Coil Ties,Two Strut Coil Tie,Coil Bolt,Straight Coil Loop Insert,Double Flared Coil Loop Insert,Single Flared Coil Loop Insert,Double Flared Loop Insert,Wire Rope Loop,Thin Slab Coil Insert,Expanded Coil Insert,Flared Thin Slab Coil Insert.

The coil insets refer to kinds of products such as:Coil Ties,Two Strut Coil Tie,Coil Bolt,Straight Coil Loop Insert,Double Flared Coil Loop Insert,Single Flared Coil Loop Insert,Double Flared Loop Insert,Wire Rope Loop,Thin Slab Coil Insert,Expanded Coil Insert,Flared Thin Slab Coil Insert.

Sandwich Panel Erection Anchor is designed to erect precast, insulated sandwich panels with a minimum loss of insulation. The anchor uses standard Fleet-Lift recess plugs and ring clutches.
 

The Fleet Lift Sandwich Panel Erection Anchor is designed to erect precast, insulated sandwich panels with a minimum loss of insulation. The anchor uses standard Fleet-Lift recess plugs and ring clutches.
The S Sandwich Panel Erection Anchor is designed for use with 2", 3" and 4" thick insulated sandwich panels. The design of the anchor allows it to distribute anchor loads evenly to both concrete wythes. This is accomplished by the use of two specially bent rebars per sandwich panel anchor. The sandwich panel erection anchor, with its unique anchor head shape, in combination with the two bent rebars, transfers both the anchor's shear and tension loads evenly into each of the concrete wythes.
Place one bent rebar through the anchor's top hole and the second rebar through the anchor's bottom hole. The rebar extend from the anchor into the top and bottom wythe of concrete. The two specially bent rebar must be used with the sandwich panel erection anchor to achieve the safe working loads shown.
 

T Anchor is a versatile anchor available in many sizes and lengths. Its high pullout strength allows it to be used for back-stripping and erection. T-Anchors can be placed on the face, back or edge of panels allowing for back-stripping and rotation from horizontal to vertical.

S Anchor is a high-strength, hot-forged anchor.When the S anchor is used with the Fleet-Lift high-capacity ring clutches, safe working loads up to 12,000 pounds can be realized. See the chart for appropriate anchor lengths and concrete compressive strengths.

Flat Foot Anchor is a versatile anchor that can be used to back-strip and transport thin panels. This anchor may also be used to erect the panels. The anchor's safe working load may be increased.

Fleet Lift Plate Anchor is manufactured with a wide base designed to increase its pull-out capacity in concrete. The wide base allows the anchor to have an increased safe working load.

Lift Shear Bar is designed and manufactured especially for use with Fleet-Lift Erection Anchors. It is a simple, easy-to-use, yet very efficient design that transfers shear forces from the erection process deeper into the edge of a precast concrete panel. It is stronger and less expensive than a shear bar fabricated from reinforcing steel.

Forged carbon steel hubs:

Wheel hub for auto
1) Apply to most of car model
2) Standard and stable material
3) ISO Certification
4) Competitive price...

Wheel hub for auto
1) Apply to most of car model
2) Standard and stable material
3) ISO Certification
4) Competitive price...

(1) Various types: DIN Type, JIS Type,US Type,and so on.
(2) Materials: AISI 316, AISI 304
(3) Size:All size is ok....

1.Material:Steel;
2.sheet metal stamping (oem);
3.Tolerance:0.05-0.10mm;
4.Lead time:in 20 days;
 

sheet metal stamping parts car parts
1 bendling, welding,laser cut ,ect
2 CNC advance machine
3 Pecision process...
 

Line suspension long-rod composite insulators:

NOMENCLATURE LIST OF LINE SUSPENSION LONG-ROD COMPOSITE INSULATORS

SYMBOLIC NOTATION OF THE LONG-ROD COMPOSITE INSULATOR

Electrical Power Fittings Product Information:
Material:
We have three materials for alterative
1. Black Heart Malleable Cast Iron: ISO 5922 (Malleable Cast Iron) Grade 350-10 (EN 1562, ASTM A197, GB9440-88)
2. Ductile Cast Iron: ASTM A536 65-45-12 or 60-40-18 (EN 1563 450-12 or 400-18) GB/T1348
3. Low Temperature Ductile Cast Iron: EN 1563 380-18LT
Product Standard:
IEC120 1984 with Ball & Socket 11-32 (GB/T 4056 and JB/T 8178-1999)
Ball & Socket of ANSI 52.3 & 52.5 & 52.8 & 52.11
Description:
The Type: Caps, Flanges, Bases,end fittings and other product
The Ball & Socket Size: (11-32)
The Mechanical Load Rating: 40-550KN
The Tube reference: 023-550
With or without Zinc Collar (For AC or DC Insulator)
Surface:
Hot-dipped Galvanizing according to ISO1461 (IEC383-1983)
Three Thicknesses to meet different requirements:
Thickness level table Zinc thickness requirements Thickness code (1) Guaranteed values
Each piece Total sampling
Normal galvanizing N 87 µm 107 µm
Reinforced galvanizing G 114 µm 128 µm
Super Reinforced galvanizing S 127 µm 140 µm
 

1)pressed coupler, right angle, swivel coupler

2) size:48.6x48.6mm

3) High precision metal stamping

4) surface: ele-electro galvanization, hot dip galvanization, self-coloured

5) weight:0.66kg

6)used for bracing and allowing tubes to be connected at any angle

Right angle swivel clamp, swivel coupler

Spread Anchor

With a variety of chain shackles for straight pulling, anchor shackles for multi-dimensional pulls, and many more stainless steel D shackles and bow shackles, US Cargo Control is fast becoming a leader in the industry.

 

Malleable iron pipe fitting

American standard(150PSI&300PSI)

Materials:ASTM A-197,ASTM A47.

Dimensions:ASME B16.3,B16.14,B16.39(Union Dimensions)

Threaded:ANSI B1.20.1

Size Available:1/8-6.

Specification:

1) Product: Casting Iron Parts

2) Material: Grey iron GG15, GG20, GG25, GG30, GG35, Ductile iron GGG40, GGG50, GGG60, GGG70, Malleable iron ASTM 32510, 35018 etc.

3) Processing: Green sand casting, Furan resin sand casting, Shell Casting

4) Weight range: 0.1kg - 800kg

5) Application: industrial parts, machinery parts, construction parts, hardware, valve/valve parts, pipe fitting, manhole cover, train accessories, insulator fittings, craft, agricultural machinery parts etc.

6) Standard: JIS, ANSI, DIN, GB, BS.

7) OEM and ODM are welcomed.

8) Quality comes first and price is competitive.

Our company JCD Group is a professional manufacturer and exporter of high-quality casting, forging and punching parts in Qingdao, China. Our products refer to industrial parts, machinery parts, construction parts, valve/valve parts, pipe fitting, agricultural machinery parts etc. If you are interested in our products, please contact me freely, I will do my best to meet your requirement.

ISO9001, 2000 Certificate
OEM is acceptable.
Good quality and low price
Contace us without hesitation

* Material: Ductile Iron, Carbon Steel, Grey iron
* Sand and investment casting(precision casting)are all avalable
* Software for drawing: PRO/E, Auto CAD, UG, CAD, PAF and Solidwork 2008 flow analysis
* Further machining work: Turning and cutting, milling, grinding, drilling, reaming and threading
* Euipment: Many CNC center and lathes.
* Surface finish process: Shot blast, chromate plating, power coated and anodizing
* OEM/ODM parts range: Auto parts, electronic parts, furniture parts, home appliance and other industrial uses
* Process: CAD surface, matel processing, surface plating, QC testing and packaging
* Made according to customers' drawing, sepecification or/ and samples
* Castng capacity: 200 tons to 500tons/per month.

Specification:

1) Product: Casting Iron Parts

2) Material: Grey iron GG15, GG20, GG25, GG30, GG35, Ductile iron GGG40, GGG50, GGG60, GGG70, Malleable iron ASTM 32510, 35018 etc.

3) Processing: Green sand casting, Furan resin sand casting, Shell Casting

4) Weight range: 0.1kg - 800kg

5) Application: industrial parts, machinery parts, construction parts, hardware, valve/valve parts, pipe fitting, manhole cover, train accessories, insulator fittings, craft, agricultural machinery parts etc.

6) Standard: JIS, ANSI, DIN, GB, BS.

7) OEM and ODM are welcomed.

8) Quality comes first and price is competitive.

Our company JCD Group is a professional manufacturer and exporter of high-quality casting, forging and punching parts in Qingdao, China. Our products refer to industrial parts, machinery parts, construction parts, valve/valve parts, pipe fitting, agricultural machinery parts etc. If you are interested in our products, please contact me freely, I will do my best to meet your requirement.

Butt welding tee

CARBON STEEL ECCENTRIC REDUCER
1.size:1/2"-24"(DN15-DN600)
2.thickness:Sch10-Sch160,XXS,XS,STD
3.standard:ASME B16.9, etc

Detailed Product Description

Steel Pipe Nipple :
American Standard : ASTM A733 / Pipe: ASTM A53 / ASTM A106 / Threads: ANSI B1.20.1
British Standard : BS
 

Steel Pipe Nipple :
American Standard : ASTM A733 / Pipe: ASTM A53 / ASTM A106 / Threads: ANSI B1.20.1
British Standard : BS EN10241 / Pipe: BS1387 / Threads: ISO 7/1
DIN Standard : DIN2982 / PIPE: DIN2440 / Threads : DIN2999
Steel Merchant Coupling:
American Standard : ASTM A865 / British Standard : BS EN10241 / DIN Standard : DIN 2999

Square Head Plug         

SPECIFICATION:
DIM. SPEC: ANSI B16.11 , MSS SP-79
MATERIAL SPEC: ASTM A105 , SS304, SS304L, SS316, SS316L
 

TYPE:     ELBOW, CROSS, STREET ELBOW, TEE, BOSS, COUPLING, HALF COUPLING, CAP, PLUG, BUSHING, UNION, SWAGE NIPPLE, BULL PLUG, REDUCER INSERT, PIPE NIPPLE ETC

THREADED (NPT OR BSP) OR SOCKET-WELD

SIZE RANGE : 1/8"-4"(6mm-100mm)

SPECIFICATION:
DIM. SPEC: ANSI B16.11 , MSS SP-79
MATERIAL SPEC: ASTM A105 , SS304, SS304L, SS316, SS316L

Threaded Elbow 

SPECIFICATION:
DIM. SPEC: ANSI B16.11 , MSS SP-79
MATERIAL SPEC: ASTM A105 , SS304, SS304L, SS316, SS316L
 

TYPE:     ELBOW, CROSS, STREET ELBOW, TEE, BOSS, COUPLING, HALF COUPLING, CAP, PLUG, BUSHING, UNION, SWAGE NIPPLE, BULL PLUG, REDUCER INSERT, PIPE NIPPLE ETC

THREADED (NPT OR BSP) OR SOCKET-WELD

SIZE RANGE : 1/8"-4"(6mm-100mm)

SPECIFICATION:
DIM. SPEC: ANSI B16.11 , MSS SP-79
MATERIAL SPEC: ASTM A105 , SS304, SS304L, SS316, SS316L

The main products of our company include:

(1)DIN 2573 PN6 DIN 2576 PN10 DIN2502 PN16 DIN2503 P25-40 DIN2566 PN16 ,DIN2631-2635 RST37.2 OR C22.8 carbon steel flange

(2)ANSI B16.5,A105 150LB 300LB 600LB 900LB 1500LB 2500LB WNRN SORF BLRF THRF SWRF LJRF carbon steel flange

(3)JIS SS400 OR SF440 5K 10K 16K 20K 30K SOPFF SOHFF BLFF carbon steel flange

(4) UNI 2276 2277 2278 6084 6089 6090 2544 2282 6091-6093 carbon steel flange

(5) EN1092 PN6 PN10 PN16 PN25 PN40 TYPE1 TYPE2 TYPE 5 TYPE 12 TYPE 13 carbon steel flange

(6)BS4504 SANI1123 1000/3 1600/3 2500/3 T/D T/E T/F carbon steel flange

(7) AS2129 TABLE D  TABLE H  TABLE E carbon steel flange

(8) GOST 12820-80 12821-80  carobn steel FLANGE.

Long teeBRITISH STANDARD
MATERIAL STRENGTH: BS EN 1562-1997
FINISH: BS EN 1461-199

Features:

 1) Material: ductile cast iron ASTM-A536

 2) Reducing installation costs

 3) Flexibility and rigidity

 4) Joint reliability

 5) Isolate noise and vibration

 6) Convenient joint

 7) Application: Power plant; Heating,ventilation and air conditioning; Industrial plant; Water treatment; Plumbing; Fire protection; Mining and mine processing; Oil field; Marine. This kind of coupling is designed for the pipe bearing moderate pressure. It allows controlled angle, linear and rotational movement at each joint and provides the added advantages of expansion, contraction and deflection. This is usful to accommodate uneven laying surfaces, and movement from thermal changes, setting, seismic effect or other causes. Flexible coupling can be used in fire protection system, feed water, gas system and etc.

Packing: Carton, pallet, container

Dimensions:

Features:

 1) Material: ductile cast iron ASTM-A536

 2) Reducing installation costs

 3) Flexibility and rigidity

 4) Joint reliability

 5) Isolate noise and vibration

 6) Convenient joint

 7) Application: Power plant; Heating,ventilation and air conditioning; Industrial plant; Water treatment; Plumbing; Fire protection; Mining and mine processing; Oil field; Marine

 Packing: Carton, pallet, container

 Dimensions:

foot anchors:

Size:

1.3T,2.5T,4T, 5T,10T for precast systems. The products are in 4 times broken load. St52-3 material.  Tensile Load test for each batch!

lifting anchor

Features:
1) Material: St52.3 or stainless steel.
2) Specification: 1.3T 2.5T 4T 5T 7.5T 10T 15T 20T 32T .
3) Surface: plain, Zinc plating, H.D.G.
4) Products available: We're manufactuer specialized in producing Swift Lift hardware to lift and handle precast concrete elements series.

Casted Wing Nut

 Very Good Casted Manufacturing Ability for All types of casted Nuts

1. Material Ductile Iron

2. Sizes: Dia 12/15/17/20mm

3. Weight: Different

4. Surface: White  Zinic or Yellow Zinic

5. Screw Pitch: 4.23mm/6.35mm/10mm

6. Thread: Machine Tap or casted

7.different types of wing nut.

8.very good casted ability.

formwork accessories:

1)Material:carbon steel
2)Size:15/17mmX80mm,90mm,100mm,120mm,200mm,300mm,1000mm,6000mm
3)Finish:black and hot-dip galvanized .
4)Offer OEM.

Edge protection safety guard rail post:

Scaffolding prop,Steel prop,Steel scaffolding

1. Reputed manufacturer on steel Scaffolding prop since 1996
2. Scaffolding Prop material: steel Q235, hotstrip by cold rolled
3. Widely used as construction tools for concrete support
4. Prop thickness available: 1.6mm, 1.8mm, 2.0mm, 2.2mm, 2.5mm, 3.0mm, 3.5mm, 4.0mm
5. Outer tube available: ¢76mm, ¢70mm, ¢60mm, ¢56mm, ¢48mm
6. Inner tube available: ¢60mm, ¢48mm, ¢40mm
7. Top/Bottom plate: Flat Square / flower plate, U-head
8. Anti-rust coating: Powder coated, cold galvanized
9. Loading capacity tested, manufactured to BS4074 and tested to BS55 

Scaffolding props

Detailed Description
1) heavy duty and light duty
2) Painted, powder coating, or hot dipped
3) Many types.

pressed fixed coupler

Pressed fixed coupler:reach to EN74,BS1139,Class A-B
Size:48.6x48.6mm
N.W.:065kg
Thickness:3.0mm
Surface:Galvanized

Scaffolding Part Type: Scaffolding Couplers.

REBAR SPLICE

THIS COUPLER IS MADE OF 45# CARBON STEEL .

THE COUPLER IS USED TO LINK REBARS WITH DIA FROM 14MM TO 40MM .

THE TENSILE STRENGTH HAS REACHED 595MPA

TECHNICAL DATA

High tensile lifting clutch

Size:1.3T,2.5T,5T,10T for precast systems.

The products are in 6 times broken load. And all the products are 100% tested.

T bolt

T bolt